Maytag 1800 W - 2005 Specifications download pdf (Page 22)

Disassembly Procedures

To avoid risk of electrical shock, personal injury or

death; disconnect power to unit before servicing.

Oven Sensor

1. Remove power from unit.

2. Open oven door and remove screws securing sensor

to oven cavity.

NOTE: Gently pull wiring through cavity wall.

3. Disconnect oven sensor at the connector terminal

and remove.

4. Reverse procedure to reinstall sensor.

NOTE: Verify sensor wires are pushed through the

insulation.

Front Side Trim

1. Remove power from unit.

2. Slide unit out far enough to access side trim.

3. Remove screws securing front side trim piece(s) to

oven chassis (left and right trim pieces).

4. Gently grasp trim piece with both hands, pull forward

and roll trim piece off retainer clips.

5. Reverse procedure to reinstall front side trim piece(s).

Oven Light Bulb/Oven Light Socket

NOTE: Requires removal of unit to replace oven light

socket.

The light automatically comes on when the door is

opened. The light will not operate during a clean cycle.

1. Remove power from unit.

2. Open oven door and locate oven light.

3. Grasp lens cover and pull outward on one side to

gain access to bulb.

4. Carefully remove old bulb, by lifting bulb straight out

of ceramic base.

NOTE: To avoid damaging the new bulb and

decreasing life of the bulb, do not touch new

bulb with bare hands or fingers.

Hold with a cloth or paper towel.

NOTE: Proceed with the following steps for oven light

socket removal.

5. Remove unit from installation position, see

“Removing and Replacing Range” procedure.

6. Disconnect or unplug the power cord leading from

unit to fuse box or junction box depending on unit.

7. Carefully displace fiberglass insulation away from

rear of light socket.

8. Release metal tabs on light socket and push socket

assembly away from the oven cavity.

9. Label and disconnect wires from light socket.

10.Reverse procedure to reinstall light socket.

Reposition insulation around lamp socket.

NOTE: Reposition fiberglass insulation around light

socket to eliminate the possibility of any heat

related problems.

Lens

Bulb

Socket

Bulb specifications

G5.3 Type Halogen Bi-Pin 25W-120V

Oven Light Switch

1. Remove power from unit.

2. Remove control panel, see "Control Panel"

procedure.

3. Remove screws securing oven light switch to front of

oven chassis.

3. Reverse procedure to reinstall oven light switch.

Convection Fan

1. Remove power from unit.

2. Remove screws securing convection motor cover to

oven chassis (screws at 12, 4 & 8 o'clock positions).

3. Remove screws securing convect motor to chassis.

4. Gently slide convection motor into oven cavity.

5. Label and disconnect electrical connection.

6. Replace and reverse procedure to reinstall motor.

Oven Vent/Smoke Eliminator

1. Remove power from unit.

2. Locate tabs on bottom of smoke eliminator and turn

counterclockwise to release locking ears.

3. Gently pull smoke eliminator down and align locking

ears with notches in oven cavity to remove.

4. Reverse procedure to reinstall smoke eliminator.

Hi-Limit Thermostat

1. Remove maintop assembly, see "Maintop Assembly"

procedure.

2. Remove screws securing hi-limit thermostat to oven

chassis.

3. Reverse procedure to reinstall hi-limit thermostat.

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 54 55

Comments to this Manuals

No comments

Maytag 1800 W - 2005 Specifications Page 22

Comments to this Manuals

Related products and manuals for Microwaves Maytag 1800 W - 2005