Maytag MDE17PR Specifications Page 20

  • Download
  • Add to my manuals
  • Print
  • Page
    / 44
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 19
ELECTRONICCONTROL SETUP
Electrical Shock Hazard
Disconnect power before servicing,
Replace all parts and panels before operating.
Faiiure to do so can result in death or
electrical shock,
IMPORTANT
E|ectrostatic Discharge (=:SD)
Sensitive Electronics
ESD problems are present everywhere. ESD may damage
or weaken the electronic control assembly. The new control
assembly may appear to work well after repair is finished,
but failure may occur at a later date due to ESD stress.
[] Use an anti-static wrist strap. Connect wrist strap to green
ground connection point or unpainted metal in the appliance.
-OR-
Touch your finger repeatedly to a green ground connection point
or unpainted metal in the appliance.
[] Before removing the part from its package, touch the anti-
static bag to a green ground connection point or unpainted
metal in the appliance.
[] Avoid touching electronic parts or terminal contacts; handle
electronic control assembly by edges only.
[] When repackaging failed electronic control assembly in anti-
static bag, observe above instructions.
GENERAL USER INFORMATION
Blank display
This condition indicates the appliance is inoperative. Enter set-up
mode to view diagnostic code.
'0 Minutes' showing in display
This condition indicates the appliance cannot be operated. Coins
dropped or debit inputs during this condition will be stored in escrow
but cannot be used until normal operation is restored by opening
and closing the door. If a door switch fails, it must be replaced before
normal operation can be restored.
Cold Start (initial first use)
Appliance is programmed at the factory as follows:
[] 5 minutes dry time/quarter (coin 1).
[] $1.50 dry price (fixed cycle with top off - PD Models).
[] $0.00 dry price (fixed cycle - PR Models).
Warm Start (after power failure)
A few seconds after power is restored, if a cycle was in progress
at the time of the power failure, 'RESELECT CYCLE' will flash
in the display. This is to indicate the need for a fabric setting
key pad to be pressed to restart dryer.
Pricing
After the door is opened following the completion of a cycle, the
display indicates the cycle price (unless set for free operation). As
coins or debit inputs arrive, the display will change to lead the user
through the initiation of a cycle.
There are four (4)types of pricing:
Fixed 'Vend' Pricing
A dryer set up for 'Fixed Cycle' operation can only accept additional
time accumulated by increments equal to the length of a complete
dry cycle. A maximum of 99 minutes may be purchased; no
additional credit is given when 99 minutes is in the display.
Accumulator Pricing
If the price is set to one coin 1, then accumulator mode is in effect.
Cycle time can be purchased one coin at a time (PD models) up to
the maximum time of 99 minutes. Stacked PD machines will credit
all money to a cycle with a single button press while in accumulator
pricing.
Fixed Cycle With Top Off Pricing
A dryer set to offer 'Top Off' capability wilt allow time to be added to
an existing dry cycle in increments equal to the number of minutes
of dry time per quarter (coin 1), up to 99 minutes, regardless of the
cost required to start the machine. No credit is given for coins or
debit inputs entered when the control is displaying 99 minutes. PR
Models: In Enhanced Debit Mode, the top off price can be set
independently. (SeeVALUE OF COIN 2), and the top off time is
calculated according to the following equation:
top off price = top off time
full cycle price full cycle length
Penny increment offset is not applied to top off purchases.
Free Cycles
This is established by setting the cycle price to zero. When this
happens 'SELECT CYCLE' will appear rather than a cycle price.
Debit Card Ready
This appliance is debit card 'cable' ready. It wilt accept a variety of
debit card systems; but, does NOT come with a debit card reader.
Refer to the debit card reader manufacturer for proper machine
set-up. In models converted to a Generation 1 debit card system,
debit pulses represent the equivalent of one coin (coin 1).
2O
Page view 19
1 ... 19 20 21 ... 44

Comments to this Manuals

No comments