Maytag LDE8604AAL Specifications

1W10214569B www.maytagcommerciallaundry.comINSTALLATION INSTRUCTIONS MFS80, MFS100, MFS125, MFS180, MFS230, MFS275 COMMERCIAL WASHERTABLE OF CONTENTS

10Electrical ConnectionCheck the data plate to determine electrical requirements. Before making the electrical connection, make sure the voltage and f

11Main Power Inlet ConnectionAdaptation of Conductor Ends of Supply Cable1. Protective conductor2. Phase conductor3. Phase conductor4. Phase conducto

12Connecting Liquid Soap Supply SystemsAll models come with a liquid soap connection.Always use liquid soap pumps that have a ow rate high enough to

13Remove Shipping BracketsIMPORTANT: Shipping brackets must be removed before putting the washer into service. Failure to do so can cause damage to th

14Remove Shipping Brackets (cont.)Models MFS180, MFS230, MFS2751. Remove the rear lower panel and side panels.2. Remove the rear shipping bracket

15Complete Installation 1. Be sure that the shipping brackets are removed. 2. Models with Tilting Feature: Remove the braces securing the vibrat

16Maintenance ScheduleAfter Each Load Remove debris from the wash drum including paper clips, coins, and other hard items. When not in use, leave

17Vibration Switch Adjustment and Function TestThe Vibration Switch is a critical component of the washer that avoids washer damage during extraction

18Verifying the Vibration Switch Function 1. Open the control panel cover. 2. Start the extraction mode. 3. After reaching maximum RPM, switch ov

19Belt ReplacementIMPORTANT: To avoid damage, do not use a pry bar to force the belts over the pulley grooves. 1. Loosen the pulley bolts on the rear

2WASHER SAFETYIMPORTANT: This washer must be directly wired to the electrical system and may not be attached with a plug. The circuit must be a d

20LubricationLubrication PointsGrease bearings and seals with a grease gun slowly, not faster than 5 strokes per minute. This avoids seal deformation

21Thrust of Door SealIf there is a water leakage around the door, the door position may have shifted and is out of position or the door seal thrust m

22Spring UnitModels MFS80, MFS100, and MFS125:Adjust the spring units if a suspension part is not horizontal (without wash load and water) or after th

23Door Will Not UnlockPossible Cause A power outageSolutionIf a cycle has started: Microprocessor version: The door cannot be opened.If a cycle ha

24REMOVING THE WASHER FROM SERVICEDisconnecting the Washer1. Disconnect the washer from electricity. 2. Turn off power at the main switch on the re

25DIMENSIONS AND TECHNICAL SPECIFICATIONS (Models MFS80, MFS100, and MFS125) 1. Front panel with operating elements 2. Electric switchboard cover

26Torque SpecificationsRecommended Torque Values for Steel BoltsBolt Size TorqueM16 x 160 mm 155 ft. lbs. (210 Nm)Dimensions and Connections Washer C

27Technical Specications (Models MFS80, MFS100, and MFS125) * Maximum dimensions, including protruding parts –6% to +10% of the voltage supply +1 Hz

28 MFS80 MFS100 MFS125Washing FunctionsWashing 38 RPM 38 RPM 38 RPMHigh Extracting 830 RPM 830 RPM 830 RPMG-Factor Max. 350 Max. 350

29DIMENSIONS AND TECHNICAL SPECIFICATIONS (Model MFS180) 1. Operator panel 2. Data plate 3. Compressed air supply 4. Main switch 5. Electri

3INSTALLATION REQUIREMENTSTools, Parts, and EquipmentRead and follow the instructions provided with any tools listedhere.Tools NeededWashers must be i

30Torque SpecificationsRecommended Torque Values for Steel BoltsBolt Size TorqueM10 x 160 mm 36 ft. lbs. (49 Nm)Dimensions and Connections Washer Cap

31DIMENSIONS AND TECHNICAL SPECIFICATIONS (Models MFS230 and MFS275) 1. Operator panel 2. Electric switchboard cover 3. Soap dispenser 4. Har

32Torque SpecificationsRecommended Torque Values for Steel BoltsBolt Size TorqueM10 x 160 mm 36 ft. lbs. (49 Nm)Dimensions and Connections Washer Cap

33Technical Specications (Models MFS180, MFS230, and MFS275) * Maximum dimensions, including protruding parts –6% to +10% of the voltage supply +1 H

34 MFS180 MFS230 MFS275Washing FunctionsWashing 36 RPM 35 RPM 34 RPMHigh Extracting 750 RPM 725 RPM 700 RPMG-Factor Max. 350 Max. 35

35DIMENSIONS AND TECHNICAL SPECIFICATIONS (Models MFS230 and MFS275 with Tilting Feature)Dimensions and Connections Washer Capacity 230 lbs(104 kg) 2

W10214569B 11/2012 Printed in the Czech Republic®/TM © 2012 Maytag. All rights reserved.

4Side View1. Washer contour line2. Washer foot3. Waste sump4. Drain with elbowSpacing Washers require 2.4 ft (0.7 m) above the top for maintenance.

5Product DimensionsSee “Technical Specications” for specic measurements on each washer size.1. Washer contour line2. Washer foot3. Waste sump4. Drai

6NOTE: Connecting these washers to an IT power supply requires special consideration. A separate grounding wire is recommended if codes permit. It

7Connection of the Main Power Inlet 1. Main switch 2. Strain relief 3. Sag of inlet cable123Connection to WasherThese washers were designed

8Transport, Handling, Inspection, and StorageINSTALLATION INSTRUCTIONSNOTE: Refer to "Equipment for Handling, Transport, and Storage" under

9Water HardnessDetermine the water hardness level in water supply. Good wash results are dependent on water hardness. In areas that have medium and ve