Installation instructionsDishwasherTo prevent accidentsand machine damage,read these instructionsbeforeinstallation or use.UVM.-Nr. 05 620 922
Prefinished modelsMachine heights between 35" and37" (889 - 940 mm) can be obtainedif the supplied legs are removed andextended legs are att
1. Install the steam deflectorA stainless steel steam deflector issupplied to protect the countertopsfrom steam and condesation when thedishwasher is
2. Install the mountingbracketsTo ensure stability, this dishwashershould be securely attached to thecountertop with the two mountingbrackets included
4. Install the dishwasher underthe countertopThe dishwasher must be installed sothat the water and electricity suppliescan be accessed through an adja
5. Level the legs^ The rear leveling legs can beadjusted with a T20 Torx screwdriverby turning the screws at the front ofthe slide skis.To raise the m
6. Install the control panelDishwashers with a selector knobThe dishwasher must not be operated without the control panel installed.^ Press the "
Dishwashers with insertable push buttons^ Press the "On/Off" button in and placethe cover, a, over the push button.^ Insert the drying vent
Dishwashers with fixed push buttons^ Press the "On/Off" button in and placethe cover, a, over the push button.^ Push the drying vent grill,
7. Align the control panelThe control panel should be alignedwith the drawer fronts of the adjoiningkitchen cabinets by adjusting the fillerstrips.^ U
8. Install the custom doorpanelA custom door panel matching thekitchen cabinetry can be installed usingthe provided templates and bracket.X = Panel le
IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3INSTRUCTIONS IMPORTANTES SUR LA SÉCURITÉ . . . . . . .
Maximum panel weightA custom door panel must not exceedthe listed maximum weight. Anoverweight panel will distort the doorsprings causing the dishwash
^Place a template on each end of themounting bracket as shown, makingsure the rule marks face the outsideof the bracket.^Hang the mounting bracket on
^Tape the bracket to the door panel tohold it in place while the mountingholes are drilled.^Drill pilot holes for the screws using a3/32" (2.5 mm
^Attach the panel to the dishwasherby aligning the bracket tabs with theslots on the door.^Open the dishwasher door slightly. Ifthe locking screws on
If the adjacent cabinetry (orappliance) does not have drawersand alignment to a drawer line is notpossible:^ Hang the bracket on the machinedoor, with
^Attach the panel to the dishwasherby lining up the bracket tabs with theslots on the door.^Open the dishwasher door slightly. Ifthe locking screws on
9. Secure the dishwasher^Open the dishwasher door.If the steam deflector is installed, themounting bracket holes must alignwith the slots in the steam
For openings exactly 173/4" (45 cm) or235/8" (60 cm) wide:^ Open the dishwasher door andremove the caps covering themounting holes on the ou
10. Adjust the door springs^Open the dishwasher door halfway.If the door remains in this position whenreleased, the springs are adjustedcorrectly.If t
11. Make the plumbingconnectionsAn air gap is built into the water inletsystem to prevent potable water frommixing with waste water.The dishwasher can
InstallationInstallation, maintenance andrepair work should be by a Mieleauthorized service technician. Work byunqualified persons could be a hazardan
Existing plumbing:If the standard3/8" copper plumbing fora dishwasher already exists with acompression fitting and valve aspictured:^ Cut the3/8&
Drainage system specifications:The machine comes equipped with:–A 5 ft. long (1.5 m) flexible drain hosewith an internal diameter of7/8"(22 mm).
Venting the drainage systemIf the dishwasher drain hose isconnected to a floor drain or to adrain pipe that is less than 8" (20 cm)above the floo
12. Make the electricalconnectionGROUNDING INSTRUCTIONSTHIS APPLIANCE MUST BEGROUNDED.In the event of a malfunction orbreakdown, grounding will reduce
Power outletThe power outlet for the appliance mustbe installed within a cabinet, on a walladjacent to the undercounter space inwhich the dishwasher i
13. Test the unitOnce the dishwasher is level andsecured it should be tested.^Remove all packing and literaturefrom inside the unit.The yellow Child S
14. Install the toekickFor installations using a continuoustoekick or a cabinet matching toekickBefore installing the toekick,measurements must be tak
For installations using the includedplastic toekickG 600 Series dishwasher^ Insert the mounting bracket with theflange pointing toward the center ofth
The included toekick will fit withoutmodification if the machine is set to itsmaximum height and the toekick isrecessed as far as possible (4" /
^Carefullyopen the dishwasher dooruntil it hits the toekick.^ Using the frontlower edge of thedoor panel as a guide, draw a lineacross the toekick.^ U
Electrical safetyBefore installation, make sure thevoltage and frequency listed on thedata plate correspond with thehousehold electrical supply. This
M.-Nr. 05 620 922 / 01Alterations rights reserved / (NovoplusB,P,S) / 2703This bio-friendly paper was bleached without the use of chlorine.
InstallationL’installation et les travaux de répa-ration et d’entretien doivent être ef-fectués par un technicien de serviceautorisé Miele. Les travau
Sécurité électriqueAvant l’installation, s’assurer que latension et la fréquence énuméréessur la plaque signalétique correspon-dent à la source d’élec
Disposal of the packingmaterialThe cardboard box and packagingprotect the appliance during shipping.These materials are biodegradable andrecyclable. P
G 600 Series DishwashersFull size models G 636 - G 698Removing the leg extensionsThe black leg extensions can beremoved to reduce the height of themac
G 800 Series DishwashersFull size models G 836 - G 898Slimline models G 801 - G 832Machine heights of 35" - 37"(889 - 940 mm) can be obtaine
Comments to this Manuals