Maytag JUC2450ARS Operations Instructions download pdf (Page 28)

13. Relocate the light striker plate to the opposite end of

the door, lining up the two holes in the striker plate,

with the two holes at the opposite center of the

door. Remove the two hole plugs (select models)

and resecure the striker plate with the two screws.

For custom wood frame model, skip to step 21.

14. Lift the door or stainless steel frame overlay end

up, opposite of where the door lock was previously

located and insert the lock from the front side.

Hold the lock in place and gently lower the door or

stainless steel frame overlay back down.

Black or white framed model: Use the 15 mm

deep-well socket and wrench.

Stainless steel frame overlay: 15 mm open-end

wrench.

Reassemble the door lock’s retaining nut to the

lock. Follow step 15 before tightening the door

lock’s nut.

15. Reassemble the Phillips screw, lock washer and

lock cam back into the lock in the order they were

removed. Position the door lock’s cam so that it

projects upward from the top of the door. Make

sure the key slot on the front is aligned vertically,

from top to bottom. Lightly tighten the Phillips

screw to secure the lock assembly. Now tighten

the door lock’s retaining nut.

Stainless steel frame overlay model: Now tighten

the retaining nut.

Black or white framed model: Mark the alignment

of the door lock and then remove the Phillip’s

screw and lock cam. Now tighten the retaining

nut, then reassemble the lock cam and Phillip’s

screw.

Steps 16 – 19 are needed for stainless steel frame

overlay model only. If reversing the door on a

black or white framed model, skip to step 20.

16. Using the Phillips head screwdriver, remove the

door lock’s Phillips screw at the end of the door

lock’s extension and remove the lock cam. Set the

lock cam aside for reassembly later. Resecure the

lock extension to the lock with the Phillips screw.

17.Lay the stainless steel frame overlay face down on

a smooth surface. Align the glass door directly

over the stainless steel frame overlay so that the

lock extension will go through the hole in the glass

door that is on the opposite end of where the lock

was originally located. Look for the mounting

holes in the glass door and align these holes with

the threaded weld nuts in the overlay. Use the ten

screws removed in step 9 to resecure the stainless

steel frame overlay to the glass door.

18. Remove the door lock’s Phillips screw and reassemble

the lock cam to the lock extension and resecure.

19. Check to see that the lock easily turns a quarter

turn from vertical to horizontal.

20. Reinstall the door gasket by pressing it back into

the door channel. Make certain the door gasket is

secure and sealed. If necessary, use the small flat-

blade screwdriver to help push the arrowhead,

section of the door gasket into the gasket channel.

21. Locate the two hinges that were removed from the

right-hand side of the wine chiller. Insert the hinge

pin screw into the hinge that was on top and

tighten securely. This hinge will be the bottom

hinge on the left side of the cabinet.

22. Remove the six plastic hole plugs from the left

hand side hinge mounting holes.

23. Using the

⁄16" nut driver, mount the hinges on the

left side of the wine chiller using the six set-aside

⁄16" hex screws. Tighten screws securely.

24. Install custom wood frame panel (select models,

refer to page 7).

25. Gently lift the door up and place the door on the

bottom hinge/hinge pin assembly. Make sure the

plastic washer is installed on the bottom hinge

before placing the door on it.

26. Using the

⁄8" Allen wrench, secure the door to the

top hinge with the Allen hinge pin screw.

27. Make certain that the door swings freely, the door

gasket seals properly and the interior light goes on

and off as the door opens and closes.

28. Confirm that door lock turns a quarter turn from

vertical to horizontal and that this locks the door

closed.

29. Replace all hole plugs.

30. Reconnect the power to the wine chiller. Return

the control knob to its previous setting.

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 51 52

Comments to this Manuals

No comments

Maytag JUC2450ARS Operations Instructions Page 28

Comments to this Manuals

Related products and manuals for Wine coolers Maytag JUC2450ARS