Maytag MDB6100AWB User Manual download pdf (Page 7)

CONTROLS AT A GLANCE

Indicator Lights

The SANITIZED (select models) light illumi-

nates at the end of the cycle when condi-

tions have been met to achieve sanitization.

The

CLEAN light illuminates at the end of

the cycle and remains lit until the door

has been open for 30 seconds continu-

ously.

The

DRY light illuminates during the entire

dry period and goes out when the cycle is

completed.

The

WASH light illuminates during all rinse

and wash portions of the cycle.

The

HEATING DELAY light illuminates

when the cycle is being extended to heat

the water.

The

CLEAN and SANITIZED (select mod-

els) indicator lights will not reilluminate

after a power failure until after the next

cycle is run.

Cycles and Water Usage

AUTO CLEAN

(Select models)

Manufacturer’s recommended cycle choice

for all day-to-day soil types.

Normal dishloads vary from day to day.

Auto Clean is recommended because it

selects the number of fills and wash time

best suited for the soil level of each load.

Depending on the number of fills required

water usage ranges from 4 to 10 gallons.

HEAVY WASH

Long cycle for heavy food soils. 10 gallons.

NORMAL WASH

Medium cycle for average food soils.

Depending on the number of fills, water

usage ranges from 4 to 8 gallons.

LIGHT WASH

Short cycle for light food soils. Depending

on the number of fills, water usage ranges

from 4 to 6 gallons.

RINSE ONLY

Rinses dishes being held until there is a

full load. Controls odors. 2 gallons.

Options

TOUGH SCRUB

™

or TOUGH

SCRUB

™

PLUS

(Select models)

Select Tough Scrub

™

or Tough Scrub

™

Plus when washing loads with hard-to-

remove food soils.

Tough Scrub

™

Tough Scrub

™

Plus can be selected with

any cycle (except

Rinse Only). Depending

on which cycle is being used, selecting this

option adds fills, heat and/or wash time to

the wash cycle.

For baked-on, dried-on soils, select

Heavy

Wash

along with the Tough Scrub

™

or Tough

Scrub

™

Plus option.

ACCUTEMP

(Select models)

AccuTemp

™

provides a water temperature

check in the main wash and also in the

final rinse cycle. If necessary, the heating

element will turn on and the cycle will be

extended to heat water to the proper tem-

perature.

Select

AccuTemp

™

with any cycle (except

Rinse Only) to assure proper hot water

temperature and to enhance drying results.

SANITIZE

(Select models)

Select Sanitize with Auto Clean (select

models)

, Heavy, Normal, or Light Wash

to sanitize dishware. At the end of the

cycle, when the cycle monitor recognizes

that the proper conditions have been met,

the

SANITIZED light illuminates.

EXTRA RINSE

(Select models)

Select Extra Rinse to add a rinse to the

cycle. An extra rinse helps to improve

results in hard water situations. The extra

rinse is already built into the cycle when

Heavy Wash is selected

HEATED DRY

Select Heated Dry to turn on the heating

element during dry for enhanced drying

results. When

Heated Dry is not selected,

towel drying of some items such as plastic

and teflon may be necessary and more

moisture may be noticed adhering to the

dishwasher interior. With either dry option,

it is normal to notice vapor escaping from

the door vent.

DRAIN/OFF

To drain the dishwasher and then turn it off,

press

Drain/Off once. Press Drain/Off twice

to turn the dishwasher off without draining.

CONTROLS AT A GLANCE

NOTE:

❚ When Sanitize is selected, cycles

are monitored to assure sanitiza-

tion. Unusually low water temper-

ature will prevent the sanitization

protocol from being satisfied and

the SANITIZED light will not illu-

minate at the end of the cycle.

NOTE:

❚ Cycle times shown in the numerical

display (select models) increase or

decrease, based on each load’s

soil level, water temperature and

selected options.

1 2 3 4 5 6 7 8 9 10 11 12 ... 35 36

Comments to this Manuals

No comments

Maytag MDB6100AWB User Manual Page 7

Comments to this Manuals

Related products and manuals for Dishwashers Maytag MDB6100AWB