Maytag W10295008A User Manual download pdf (Page 4)

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. The

parts supplied are in the washer drum.

Tools needed for connecting the water inlet hoses

■ Pliers (that open to 1

/16" [39.5 mm])

■ Flashlight (optional)

Tools needed for connecting the drain hose

■ Locking pliers (that open to 1

/16" [39.5 mm])

Tools needed for installation

■ Open end wrenches 14 mm and 13 mm

■ Level

■ Wood block

■ Ruler or measuring tape

Parts supplied

A. Drain hose form

B. Inlet hose (2)

C. Inlet hose washer (4)

D. Drain hose

E. Transport bolt hole plug (4)

F. Beaded strap

G. Hose clamp

Alternate Parts

Your installation may require additional parts. If you are interested

in purchasing one of the items listed here, call the toll-free number

on the cover or in the “Assistance or Service” section.

If You Have You Will Need to Buy

Laundry tub or

standpipe taller

an 96" (2.4 m)

Sump pump system (if not already

available)

Overhead sewer Standard 20 gal. (76 L), 30" (762 mm) tall

ain tub or utility sink and sump pump

(available from local plumbing suppliers)

Floor drain Siphon break, Part Number 285834;

addition

al drain hose

Part Number 8318155; and connector kit,

Part Number 2858835

Drain hose too

sho

4 ft. (1.2 m) drain hose extension kit,

Part Number 2858863

Water faucets

eyond reach of fill

hoses

2 longer water fill hoses:

6 ft. (1.8 m) Part Number 76314

10 ft. (3.0 m) Part Number 350008

Options

Pedestal

You have the option of purchasing pedestals of different heights

separately for this washer. You may select a 10" (254 mm) or a 15.5"

(394 mm) pedestal. The pedestal will add to the total height of the

washer.

Optional pedestal

Pedestal

Height

Approximate

Height with

Washer

Color Model

Number

10" (254 mm) 46" (1168 mm) White WHP1000SQ

15.5" (394 mm) 51.5" (1308 mm) White WHP1500SQ

Stack Kit

Are you planning to stack your washer and dryer? To do so you will

need to purchase a Stack Kit.

To order, call the dealer from whom you purchased your washer or

refer to the “Assistance or Service” section. Ask for Part Number

8572546.

Location Requirements

Selecting the proper location for your washer improves

performance and minimizes noise and possible washer “walk.”

Your washer can be installed under

a custom counter, or in a

basement, laundry room, closet, or recessed area. See “Drain

System.”

Companion appliance location requirements should also be

consi

dered. Proper installation is your responsibility.

You will need:

■ A water heater set to deliver 120°F (49°C) water to the washer.

■ A grounded electrical outlet located within 6 ft. (1.8 m) of where

the power cord is attached to the back of the washer. See

“Electrical Requirements.”

■ Hot and cold water faucets located within 4 ft. (1.2 m) of the hot

and cold water fill valves, and water pressure of 20-100 psi

(137.9-689.6 kPa).

■ A level floor with a maximum slope of 1" (25 mm) under entire

washer. Installing the washer on soft floor surfaces, such as

carpets or surfaces with foam backing, is not recommended.

■ A sturdy and solid floor to support the washer with a total weight

(water and load) of 400 lbs (180 kg).

Do not operate your washer in temper

atures below 32°F (0°C).

Some water can remain in the washer and can cause damage in low

temperatures.

1 2 3 4 5 6 7 8 9 ... 51 52

Comments to this Manuals

No comments

Maytag W10295008A User Manual Page 4

Comments to this Manuals

Related products and manuals for Washers Maytag W10295008A