Maytag MSC21C6MDM Installation Guide download pdf (Page 9)

7. On some models, the ice maker is equipped with a built-in

water strainer. If your water conditions require a second water

strainer, install it in the ¹⁄₄" (6.35 mm) water line at either tube

connection. Obtain a water strainer from your nearest

appliance dealer.

Style 3

1. Unplug refrigerator or disconnect power.

2. Remove and discard the black nylon plug from the gray water

tube on the rear of the refrigerator.

3. If the gray water tube supplied with the refrigerator is not long

enough, a ¹⁄₄" x ¹⁄₄" (6.35 mm x 6.35 mm) coupling is needed in

order to connect the water tubing to an existing household

water line. Thread the provided nut onto the coupling on the

end of the copper tubing.

NOTE: Tighten the nut by hand. Then tighten it with a wrench

two more turns. Do not overtighten.

4. Turn shutoff valve ON.

5. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

Complete the Installation

1. Plug into a grounded 3 prong outlet.

2. Wait a few minutes. Check that the compressor is operating

properly and that all lights are working.

NOTE: If the refrigerator does not operate, check that the

circuit breaker is not tripped or that the household fuse has

not blown.

3. Flush the water system. See “Water and Ice Dispensers” in the

User Instructions or User Guide.

NOTE: Allow 24 hours to produce the first batch of ice. Allow

72 hours to completely fill ice container.

IMPORTANT: If construction will continue after refrigerator has

been installed, unplug refrigerator or disconnect power.

Leveling and Door Closing

Your refrigerator has two adjustable front feet — one on the right

and one on the left. In most cases, the refrigerator should be

steady when both feet are touching the floor. If your refrigerator

seems unsteady or if you want the doors to close more easily,

adjust the refrigerator’s tilt using the instructions below:

1. Move the refrigerator into its final location. Open both doors

to 90°. Remove the base grille by removing the two screws,

then pulling out on the outside corners.

NOTE: The doors must only be opened to 90°. If they are

opened all the way, the base grille will not come off.

2. The two leveling feet are located on the brackets on each side

of the product.

NOTE: Having someone push against the top of the refrigerator

takes some weight off the leveling feet. This makes it easier to

make adjustments.

3. Use a ¹⁄₄" open-ended or adjustable wrench to adjust the

leveling feet. Turn the leveling foot to the left to raise that side

of the product, or turn it to the right to lower that side of the

product.

NOTE: Both leveling feet should be snug against the floor, and

the rollers should not touch the floor. This keeps the

refrigerator from rolling forward when opening the doors.

4. Open both doors again and check that they close as easily as

you like. If not, tilt the refrigerator slightly more to the rear by

turning the leveling feet to the left. It may take several more

turns, and you should turn both leveling feet the same

amount.

5. Use a bubble level to check the leveling of the refrigerator.

NOTE: Whenever you need to move the refrigerator, turn the

leveling feet to the right until they are no longer touching the

ground. This will allow the refrigerator to roll more easily.

A. Refrigerator water tubing

B. Nut (provided)

C. Bulb

D. Coupling (purchased)

E. Ferrule (purchased)

F. Nut (purchased)

G. Household water line

A B C D E F G

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

fire, or electrical shock.

WARNING

A. Bottom hinge

B. Leveler bracket

C. Leveling foot

Raise

Lower

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 63 64

Comments to this Manuals

No comments

Maytag MSC21C6MDM Installation Guide Page 9

Comments to this Manuals

Related products and manuals for Fridges Maytag MSC21C6MDM