Maytag MEDB955FC Use and Care Manual Page 5

  • Download
  • Add to my manuals
  • Print
  • Page
    / 36
  • Table of contents
  • TROUBLESHOOTING
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 4
5
CONTROL PANEL AND FEATURES
Not all features and cycles are available on all models.
POWER
Touch to turn the dryer on and off. Touch to stop/cancel
a cycle at any time.
CYCLE CONTROL KNOB
Use your dryer’s cycle control knob to select available cycles
on your dryer. Turn the knob to select a cycle for your laundry
load. See “Cycle Guide” for detailed descriptions of cycles.
START/PAUSE
Touch and hold until the LED comes on to start a cycle
or touch once while a cycle is in process to pause it.
TIMED DRY ADJUST
Use “+” and “–” with Timed Cycles to increase or
decrease the length of a Timed Dry or Rapid Dry cycle.
LED DISPLAY
When you select a cycle, its default settings will light up and
the Estimated Time Remaining (for Sensor Cycles) or actual
time remaining (for Timed Cycles) will be displayed.
SETTINGS
Touch the setting names next to the display to adjust settings.
See “Cycle Guide” for available settings on each cycle. Not all
settings are available with all cycles.
Temperature
Timed Cycles: When using Timed Cycles, you may select
a dry temperature based on the type of load you are drying.
Use the warmest setting safe for the garments in the load.
Follow garment label instructions.
Sensor Cycles: Sensor Cycles allow temperature
adjustment. At most, 4 of available temperatures (not
including Air Only) are allowed.
Dry Level
You may adjust the Dry Level on Sensor Cycles only
(except for the Sanitize and Steam Refresh cycles), if
desired.
Wrinkle Prevent
If you will be unable to remove a load immediately, touch
Wrinkle Prevent to add up to 150 minutes of periodic
tumbling to help reduce wrinkling. On some cycles, you
may select the “With Steam” setting to add a short steam
cycle after 60 minutes to help smooth out wrinkles.
1
2
3
NOTE: If the Wrinkle Prevent option is selected, it is active
even if the done indicator is lit. If you open the dryer door
prior to the end of the Wrinkle Prevent option, the dryer
will go into Pause mode. You will need to touch Power
to turn off or touch Start/Pause to continue the Wrinkle
Prevent option. If the Wrinkle Prevent option is paused, it
will discontinue after 5 minutes of inactivity and turn off.
Audio Level
Touch AUDIO LEVEL to move the volume of the end
signal and button sounds between 5 different settings,
including OFF.
OPTIONS
Use to select available options for your dryer.
My Cycle
If you have a favorite cycle with custom settings that you
use frequently, you can use the My Cycle feature to keep
your preferred settings ready to use. To save the cycle,
press and hold MY CYCLE (approximately 3 seconds)
until a beep sounds and My Cycle LED is lit. Once a
configuration has been saved, you may power on the
machine and briefly press MY CYCLE to load your saved
cycle and settings.
Energy Saver
Activate the ENERGY SAVER setting to increase your
energy savings. This setting uses a lower heat level and
extends cycle time. Turn on for optimal energy savings.
Turn off for optimal cycle times. ENERGY SAVER is
only available for the Normal cycle and will default on.
NOTE: Energy savings may vary across loads.
Static Reduce
Touch to add the Static Reduce option to selected Sensor
cycles (see “Cycle Guide”). The dryer will automatically
tumble, pause, and introduce a small amount of moisture
into the load to help reduce static. This option will repeat
and adds approximately 8 minutes to the total cycle time.
Steam Boost
Steam Boost adds steam to the end of the cycle to help
smooth wrinkles. See “Cycle Guide.”
4
NOTE: The control panel features a sensitive surface that responds to a light touch of your finger. To ensure your selections are registered,
touch the control panel with your finger tip, not your fingernail. When selecting a setting or option, simply touch its name.
3
2
1
6
4
7
8
5
5
6
7
Page view 4
1 2 3 4 5 6 7 8 9 10 ... 35 36

Comments to this Manuals

No comments