Maytag MLG31PCB Installation Manual

RETAIN THESEINSTRUCTIONS IN A SAFEPLACE FOR FUTUREREFERENCEMLG31PCB Installation ManualPhase 7 CoinWARNING: For your safety the informationin this ma

6 Maytag 113203-3NOTE: Manufacturer reserves the right to make changes in specifications at any time without notice orobligation.SPECIFICATIONS – GAS

113203-3 Maytag 7SECTION IIIINSTALLATION PROCEDURESInstallation should be performed by competent technicians in accordance with local and state codes.

8 Maytag 113203-31. The dryer must be installed on a sound level floor capable of supporting its weight. Carpeting must beremoved from the floor area

113203-3 Maytag 98. Dryer must be located in an area where correct exhaust venting can be achieved as noted in this manual(refer to Exhaust Requiremen

10 Maytag 113203-3D. FRESH AIR SUPPLY REQUIREMENTSAir supply (make-up air) must be given careful consideration to ensure proper performance of each d

113203-3 Maytag 11E. EXHAUST REQUIREMENTSExhaust ductwork should be designed and installed by a qualified professional. Improperly sized ductwork wi

12 Maytag 113203-32. Single Dryer VentingWhere possible, it is suggested to provide a separate exhaust duct for each dryer. The exhaust ductworkshoul

113203-3 Maytag 13

14 Maytag 113203-3

113203-3 Maytag 153. Multiple Dryer (Common) VentingIf it is not feasible to provide separate exhaust ducts for each dryer, ducts from individual drye

Retain This Manual In A Safe Place For Future ReferenceThis product embodies advanced concepts in engineering, design, and safety. If this product is

16 Maytag 113203-3To protect the outside end of the horizontal ductwork from the weather, a 90º elbow bent downward shouldbe installed where the exhau

113203-3 Maytag 17

18 Maytag 113203-3F. ELECTRICAL INFORMATION1. Electrical RequirementsIt is your responsibility to have ALL electrical connections made by a properly

113203-3 Maytag 193. GroundingGrounding (earth) connections must be provided and installed in accordance with state and local codes. Inthe absence of

20 Maytag 113203-3G. GAS INFORMATIONIt is your responsibility to have ALL plumbing connections made by a qualified professional to ensure that thegas

113203-3 Maytag 212. Technical Gas Dataa. Gas SpecificationsShaded areas are stated in metric equivalents* Measured at gas valve pressure tap when ga

22 Maytag 113203-33. Piping/ConnectionsALL components/materials must conform to National Fuel Gas Code Specifications ANSI Z223.1-LATESTEDITION, or in

113203-3 Maytag 23The size of the main gas supply line (header) will vary depending on the distance this line travels from thegas meter (or in the cas

24 Maytag 113203-3

113203-3 Maytag 25H. PREPARATION FOR OPERATIONThe following items should be checked before attempting to operate the dryer:1. Read ALL “CAUTION,” “WA

IMPORTANTYOU MUST DISCONNECT AND LOCK OUT THE ELECTRIC SUPPLY AND THE GASSUPPLY OR THE STEAM SUPPLY BEFORE ANY COVERS OR GUARDS AREREMOVED FROM THE MA

26 Maytag 113203-34) The dryer will continue through the drying and cooling cycles until the time vended has expired.NOTE: The dryer can be stopped at

113203-3 Maytag 27NOTE: Water column (W.C.) pressure requirements (measured at the gas valve pressure tap):Natural Gas ...

28 Maytag 113203-3J. SHUTDOWN INSTRUCTIONSIn the case where the dryer is to be shutdown (taken out of service) for a period of time, the following mu

113203-3 Maytag 29SECTION IVOPERATING INSTRUCTIONSA. COIN MODE1. When at least one (1) of the dryer’s pockets is in the ready state and no cycle is i

30 Maytag 113203-3B. FREE MODE1. When the controller is in the ready state and no cycle is in progress, the liquid crystal display (L.C.D.)screen wil

113203-3 Maytag 31E. CLEARING CREDIT/CLEARING CYCLECredit can be cleared from either dryer pocket by using the following key combination. With the p

32 Maytag 113203-3SECTION VSERVICE/PARTS INFORMATIONA. SERVICEOnly properly licensed or trained technicians should service the dryer. If service is

113203-3 Maytag 33SECTION VIWARRANTY INFORMATIONA. RETURNING WARRANTY CARDSBefore any dryer leaves the manufacturer, a warranty card is placed on the

34 Maytag 113203-3SECTION VIIROUTINE MAINTENANCEA. CLEANINGA program and/or schedule should be established for periodic inspection, cleaning, and rem

113203-3 Maytag 35WARNING: THE ACCUMULATION OF LINT IN THE EXHAUST DUCTWORK CANCREATE A POTENTIAL FIRE HAZARD.WARNING: DO NOT OBSTRUCT THE FLOW OF COM

WARNINGThe dryer must never be operated with any of the back guards, outer tops, or servicepanels removed. PERSONAL INJURY OR FIRE COULD RESULT.IMPOR

36 Maytag 113203-3When contacting the Maytag dealer, certain information is required to ensure proper service/parts information.This information is on

113203-3 Maytag 37SECTION IXPROCEDURE FOR FUNCTIONAL CHECKOF REPLACEMENT COMPONENTSKEYBOARD (TOUCH PAD) LAYOUT1. Liquid Crystal Display2. Top Pocket H

38 Maytag 113203-31. For Models with Johnson Direct Spark Ignition (DSI) Controller (G760)Theory of Operation:Start the drying cycle. When the gas bu

113203-3 Maytag 39Optional Exhaust Duct KitP/N 882035Optional Gas Piping KitP/N 880128ITEM # QTY P/N DESCRIPTION1 1 143600 10” X 6” X 6”, Y DUCT2 1 14

Part No. 113203 3-03/15/05-14

Table of ContentsSECTION ISAFETY PRECAUTIONS...3SECTION IISP

SECTION VIIROUTINE MAINTENANCE...34A. Cleaning ...

113203-3 Maytag 3SECTION ISAFETY PRECAUTIONSWARNING: For your safety, the information in this manual must be followed to minimize the risk offire or e

4 Maytag 113203-3WARNING: DO NOT use heat for drying articles that contain plastic, foam, sponge rubber, orsimilarly textured rubber materials. Dryin

113203-3 Maytag 5SECTION IISPECIFICATIONSGASMAXIMUM CAPACITY (TOTAL DRY WEIGHT) 60 lbs27.2 kgBASKET (TUMBLER) DIAMETER 27-1/4”69.22 cmBASKET (TUMBLER)