Maytag MGC7536WW User Manual download pdf

INSTALLATION INSTRUCTIONS

for Ice Maker Drain Pump

NOTE: Connect drain pump to your drain in accordance with all state and local codes and ordinances. It may be desirable

to insulate drain tube thoroughly up to drain inlet to minimize condensation on the drain tube. Drain pump is designed to

pump water to a maximum height of 10 feet.

Kit Contains:

1 Drain Pump

1 Drain Tube,

⁄8" ID x 5

⁄8" (ice maker bin to pump

reservoir inlet)

1 Drain Tube,

⁄8" ID x 10' (pump check valve to

household drain)

1 Vent Tube,

⁄8" ID x 32" (pump reservoir vent to ice

maker cabinet back)

3 Cable Clamp (secures vent tube to back of ice maker)

3 Screw, #8 x

⁄2" (secures clamps to back of ice maker)

2 Screw, #8-32 x

⁄8" (secures pump to baseplate or ice

maker)

2 Small Hose Clamps,

⁄8" (secures vent and drain tube

to pump)

1 Large Hose Clamp,

⁄8" (secures drain tube to bin)

Please follow the steps to install the drain pump.

1. Unplug ice maker or disconnect power.

2. Remove rear cover. Carefully pull rear cover away from

drain tube.

3. Remove old drain tube and clamp attached to bin.

Discard old tube. Clamp will be reused.

Instruction Sheet 2185944 Rev. B 7/01

wWARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all panels before operating.

Failure to do so can result in death or electrical shock.

5. Install vent tube (

⁄8" ID x 32") to pump reservoir vent.

Use one (1)

⁄8" small adjustable clamp, supplied.

NOTE: DO NOT install household drain tube at this time.

6. Remove clamp and ground screw attached to ice maker

power cord which is mounted to the unit base. Clamp

and screw will be reused.

(continued)

4. Install new drain tube (

⁄8" ID x 5

⁄8") to pump reservoir

inlet using old clamp from step 3. See Figure 1.

Figure 1

⁄8" Adjustable

hose clamp

Drain tube (bin to pump)

(Do not kink; trim tube

length if required)

⁄8" Hose clamp from

discarded drain tube

Drain pump

reservoir inlet

1 2 3 4 5 6

Summary of Contents

Page 1 - INSTALLATION INSTRUCTIONS

1INSTALLATION INSTRUCTIONSfor Ice Maker Drain PumpNOTE: Connect drain pump to your drain in accordance with all state and local codes and ordinances.

Page 2 - 2185944-B

22185944-B7. Coil power cord of ice maker into a 4" diameter coil.Wrap electrical tape around the power cord in severalplaces to keep the cord in

Page 3

314. Attach household drain tube (3⁄8" ID x 10') to householddrain pipe before putting ice maker in service.15. Check all connections for le

Page 4 - INSTRUCTONS D’INSTALLATION

15. Posez le tube de mise à l’air libre (3⁄8 de pouce de dia.int. x 32 po) sur la mise à l’air libre du réservoir de lapompe. Utilisez un (1) petit co

Page 5

22185944-B7. Enroulez le cordon électrique de la machine à glaçonsen un serpentin de 4 pouces de diamètre. À plusieursendroits, attachez le cordon éle

Page 6

314. Attachez le tube de vidange de l’habitation (3⁄8 depouce de dia. int. x 10 pieds) à la tuyauterie devidange de l’habitation avant de mettre la ma