WARNING: For your safety the information inthis manual must be followed to minimize therisk of fire or explosion or to prevent propertydamage, person

6NOTE: Manufacturer reserves the right to make changes in specifications at any time without notice orobligation.SPECIFICATIONS  GAS ONLY

7SECTION IIIINSTALLATION PROCEDURESInstallation should be performed by competent technicians in accordance with local and state codes. In theabsence

8B. LOCATION REQUIREMENTSBefore installing the dryer, be sure the location conforms to local codes and ordinances. In the absence of suchcodes or

9C. DRYER ENCLOSURE REQUIREMENTSBulkheads and partitions should be made of noncombustible materials and must be located a minimum of12-inches (30.48

10D. FRESH AIR SUPPLY REQUIREMENTSThe air supply (make-up air) must be given careful consideration to assure proper performance of each dryer.An unre

11E. EXHAUST REQUIREMENTSExhaust ductwork should be designed and installed by a qualified professional. Improperly sized ductwork willcreate excessi

12NOTE: As per the National Fuel Gas Code, Exhaust ducts for type 2 clothes dryers shall beconstructed of sheet metal or other noncombustible materia

13If the length of the duct run or quantity of elbows used exceeds the above noted specifications, the cross sectionarea of the ductwork must be incre

14MULTIPLE DRYER (COMMON) VENTINGHORIZONTAL VENTINGIf it is not feasible to provide separate exhaust ducts for each dryer, ducts for individual dryer

15IMPORTANT: For extended ductwork runs, the cross section area of the duct can only be increasedto an extent. For extended ductwork runs, a professi

IMPORTANT NOTE TO PURCHASERInformation must be obtained from your local gas supplier on the instructionsto be followed if the user smells gas. Thes

16IMPORTANT VENTING REMINDERS1. Ductwork size and installation should be done by a qualified professional.2. The dryer must be exhausted to the outdoo

17F. ELECTRICAL INFORMATION1. Electrical RequirementsALL electrical connections must be made by a properly licensed and competent electrician. Thisi

182. Electrical Service Specifications1/15/04IMPORTANT: Figures shown are for non-reversing models only. For reversing models contact thefactory.3. G

196LQJOH3KDVH(OHFWULFDO/HDG&RQQHFWLRQV%ODFN3RVLWLYH:KL WH RU5HG1HX WUDORU/*UHHQ*URX Q GSingle-Phase (1ø) Wiring Connections/HookupThe e

20G. GAS INFORMATIONIt is your responsibility to have ALL plumbing connections made by a qualified professional to assure that the gasplumbing instal

212. Technical Gas Dataa. Gas SpecificationsShaded areas are stated in metric equivalents* Measured at outlet side of gas valve pressure tap when gas

223. Piping ConnectionsALL components/materials must conform to National Fuel Gas Code Specifications ANSI Z223.1-LATESTEDITION, or in Canada, CAN

23Consistent gas pressure is essential at ALL gas connections. It is recommended that a 3/4-inch (19.05mm) pipe gas loop be installed in the supply l

24H. PREPARATION FOR OPERATION AND START-UPThe following items should be checked before attempting to operate the dryer:1. Read ALL CAUTION, WARNI

25I. PREOPERATIONAL TESTSALL dryers are thoroughly tested and inspected before leaving the factory. However, a preoperational testshould be performe

WARNINGUNDER NO CIRCUMSTANCES should the door switch or the heat circuit devicesever be disabled.IMPORTANTYOU MUST DISCONNECT AND LOCK OUT THE ELECTRI

26NOTE: If computer program changes are required, refer to the computer programming section of themanual supplied with the dryer.6. The dryer should b

27K. SHUTDOWN INSTRUCTIONSIf the dryer is to be shutdown (taken out of service) for a period of time, the following must be performed:1. Discontinue

28SECTION IVSERVICE/PARTS INFORMATIONA. SERVICEService must be performed by a qualified trained technician, service agency, or gas supplier. If serv

29SECTION VWARRANTY INFORMATIONA. RETURNING WARRANTY CARDSBefore any dryer leaves the manufacturers test area, a warranty card is placed on the back

30SECTION VIROUTINE MAINTENANCEA. CLEANINGA program and/or schedule should be established for periodic inspection, cleaning, and removal of lint from

3190 DAYSInspect and remove lint accumulation in customer furnished exhaust ductwork system from dryers internalexhaust ducting.WARNING: THE ACCUMUL

32SECTION VIIDATA LABEL INFORMATIONWhen contacting the Maytag dealer, certain information is required to insure proper service/parts information.This

33THE DATA LABEL1. MODEL NUMBERThe model number is an Maytag Co. number, which describes the size of the dryerand the type of heat (gas, electric, or

34SECTION VIIIPROCEDURE FOR FUNCTIONAL CHECKOF REPLACEMENT COMPONENTS1. Microprocessor Controller (Computer) Boarda. Upon completing installation of t

352. For Models with Johnson Direct Spark Ignition (DSI) Controller (G760)Theory of Operation:Start the drying cycle. When the gas burner ignites wit

WARNINGThe dryer must never be operated with any of the back guards, outer tops, or servicepanels removed. PERSONAL INJURY OR FIRE COULD RESULT.IMPOR

36SECTION IXMANUAL RESET BURNER HI-LIMIT INSTRUCTIONSA. PHASE 7This dryer was manufactured with a manual reset burner hi-limit thermostat, which is m

Part No. 113201 3-1/15/04 - 150

SECTION ISAFETY PRECAUTIONS ... 3SECTION IISPECIFICATIONS ...

SECTION VIIIPROCEDURE FOR FUNCTIONAL CHECK OF REPLACEMENTCOMPONENTS ...

3SECTION ISAFETY PRECAUTIONSWARNING: For your safety, the information in this manual must be followed to minimize the risk offire or explosion or to p

4WARNING: DO NOT use heat for drying articles that contain plastic, foam, sponge rubber, orsimilarly textured rubber materials. Drying in a heated ba

5SECTION IISPECIFICATIONSGAS0$;,080&$3$&,7< '5<:(,*+7 OEVNJ%$6.(7780%/(5',$0(7(5 ´FP%$6.(7 780%/(5